Preformed, temporary markings & surface mounted studs
We have doubled the grant rates for short course tiers 1 – 3. To address rising costs, you can now receive higher rates on course achievements from 1st April 2023
|
Grant Tier |
Achievement date before 1 April 2023 |
Achievement date on or after 1 April 2023 |
|
Grant Tier 1 Grant Tier 1 Refresher |
£30 £15 |
£60 £30 |
|
Grant Tier 2 Grant Tier 2 Refresher |
£70 £35 |
£140 £70 |
|
Grant Tier 3 Grant Tier 3 Refresher |
£120 £60 |
£240 £120 |
Overview
CITB has developed this standard in discussion with industry
Duration
Minimum of 1 day 6 learning hours
Purpose/Scope
The purpose of this standard is to provide overview knowledge of installing preformed cold thermoplastic road markings on rolls or symbols/logos. Typically for school playgrounds, factories, car parks, and increasingly on public highways.
The scope of this standard covers:
- types, uses, and performance
- main fixing methods
- how to prepare the surface
- setting out regulations: Traffic Signs Regulations and General Directions (TSRGD), chapter 5, and Road Safety Marking Association (RSMA) update your road markings
- safety: hazards, risks, controls, and safe working practices
- how to plan to install
- how to set out
- how to remove
- how to dispose of waste materials
- safety for workers and other road users
- legislation for: road users, road vehicles, and road traffic.
Occupational relevance
Training delivered against this standard is relevant to the following occupational group(s):
- operative and craft to level 2
- supervision.
Candidate pre-requisites
There are no candidate pre-requisites as part of this standard. However, it would be beneficial if candidates had experience in thermoplastic road marking operations.
Instruction/Supervision
As a minimum, course instructors must be able to demonstrate that, in relation to this standard, they have:
- a train the trainer or instructional techniques course certificate
- successfully completed training to this standard
- at least 2 years relevant industrial experience
- a verifiable CV.
Delivery
The following methods may be used in the delivery of this standard:
- practical training: off the job simulated environment (not on the roads)
- theory training: classroom
The class size and candidate/instructor ratio must allow training to be delivered in a safe manner and enable candidates to achieve the learning outcomes.
All materials and equipment must be of a suitable quality and quantity for candidates to achieve learning outcomes and must comply with relevant legislation.
Learning should include at least 25% of learning activities to suit scenario examples, and simulated practical examples.
Demonstrate operation of mobile equipment and vehicles, with delegates as passengers and observers, off the road, in a closed-access area.
Candidates may be able to try some basic practical tasks under close supervision and coaching, off the job, after a risk assessment has been completed and risks addressed. This is merely to sample the range of work types, not to gain competency.
This standard is considered to contain 51% or more practical training.
Assessment
Methods of assessment considered appropriate for training delivered against this standard are:
- practical assessment: off the job simulated environment
- theory assessment: classroom, e-learning, or a combination.
Quality assurance
Quality assurance against this standard will require initial approval of the training organisation and their content mapped to the standard.
CITB will also conduct an approval intervention, either desk-based or centre visit, to ensure the training organisation can meet the requirements of the training standard.
Approved training organisations (ATOs) will be required to present information on records of training and assessment upon request to CITB for desk based analysis. They will also be visited annually by the CITB quality assurance team.
Renewal
Recommended Refresher
Approval date
November 2018
Review cycle
Either on request or 3 years from approval date.
Learning outcomes
The candidate will be able to:
- Describe the types, uses, and performance of markings & studs
- Describe the main fixing methods of markings & studs
- Prepare the surface for markings & studs
- Describe the setting out regulations: TSRGD, chapter 5, chapter 8 part 2, RSMA update your road markings
- Describe the: hazards, risks, controls, and safe working practices
- Plan to install markings and studs
- Set out for markings & studs
- Remove markings & studs
- Dispose of waste materials
- Describe safety for workers and other road users
- Describe them main legislation for: road users, road vehicles, and road traffic
Additional information
Health & Safety Executive (HSE)
- Control of Substances Hazardous to Health (COSHH)
- Working with substances hazardous to health. A brief guide to COSHH
- Guide to PPE at Work Regulations 1992
- Standards and markings for personal protective equipment
- Safe use of work equipment (PUWER)
- Driving at work: Managing work-related road safety
- Work related road safety
- Driving at work: Managing work-related road safety
- Useful road related links
- Scottish Occupational Road Safety Alliance (ScORSA)
- Roadside precautions
- Risk assessment
- Workplace health, safety and welfare
- Workplace transport safety
- Parking
- A guide to workplace transport safety
- Vehicles at work
- Safe driving: loading & unloading
Legislation
http://www.legislation.gov.uk/
- The PPE at Work Regulations 1992
- Provision and Use of Work Equipment Regulations (PUWER) (1998 UK 1999 NI)
- The Management of Health and Safety at Work Regulations 1999
- The Health and Safety at Work etc Act 1974
- The Workplace (Health, Safety and Welfare) Regulations 1992
- Health and Safety (Safety Signs and Signals) Regulations 1996
- Fire Precautions and Workplace Regulations 1997
- Reporting of Injuries, Diseases and Dangerous Occurrences Regulations (RIDDOR) 1995
Standards
- BS EN 1436:2007+A1:2008 Road marking materials. Road marking performance for road users
- BS EN 1424:1998 Road marking materials. Premix glass beads
- BS EN 1423:2012 Road marking materials. Drop on materials. Glass beads, antiskid aggregates and mixes
- BS EN 1463-1:2009 Road marking materials. Retroreflecting road studs. Initial performance requirements
- BS EN 1463-2:2000 Road marking materials. Retroreflecting road studs. Road test performance spec’ns
- BS EN 1463-3. Road marking materials. Part 3. Active road studs
- BS EN 1790:2013 Road marking materials. Preformed road markings
- BS EN 1871:2000 Road marking materials. Physical properties
- BS EN 1871. Road marking materials. Paint, thermoplastic and cold plastic materials. Specifications
- BS 3262-3:1989 Hot-applied thermoplastic road marking materials. Specification to apply to road surfaces