Hand held line removal
We have doubled the grant rates for short course tiers 1 – 3. To address rising costs, you can now receive higher rates on course achievements from 1st April 2023
|
Grant Tier |
Achievement date before 1 April 2023 |
Achievement date on or after 1 April 2023 |
|
Grant Tier 1 Grant Tier 1 Refresher |
£30 £15 |
£60 £30 |
|
Grant Tier 2 Grant Tier 2 Refresher |
£70 £35 |
£140 £70 |
|
Grant Tier 3 Grant Tier 3 Refresher |
£120 £60 |
£240 £120 |
Overview
CITB has developed this standard in discussion with industry
Duration
Minimum 1 day of 6 learning hours
Purpose/Scope
The purpose of this standard is to provide the candidate with the knowledge and skills to remove thermoplastic road markings using a hot compressed air (HCA) lance and a hand propelled scabbler (pneumatic)
The scope of this standard covers:
- equipment types: HCA lance and a hand-propelled scabbler with compressor
- removal methods: HCA lance, dustless blasting, scabbling, and high pressure water blasting
- how to store, handle, and decant fuels such as: LPG, petrol, diesel, and oils
- safe preparation and planning to remove thermoplastic road markings
- hazards, risks, controls, and safe work practices associated with the equipment
- how to set up, pre-use safety check, maintain, shut down, set down, and store the equipment
- how to remove thermoplastic road markings using the equipment
- how to identify faults and issues with removal of thermoplastic and use of the equipment
- main legislation, codes of practice, and/or standards, including manual handling, COSHH, and traffic management.
Occupational relevance
Training delivered against this standard would be relevant to the following occupational group:
- operative and craft.
Candidate pre-requisites
For this training, it would be beneficial if candidates had a basic knowledge of road marking terminology and techniques.
Instruction/Supervision
As a minimum, course instructors must be able to demonstrate that, in relation to this standard, they have:
- a train the trainer or instructional techniques course certificate
- successfully completed training to this standard
- at least 2 years relevant industrial experience
- a verifiable CV.
Delivery
The following method(s) may be used in the delivery of this standard:
- on the job in a safe environment
- classroom
All materials and equipment must be of a suitable quality and quantity for candidates to achieve learning outcomes, and must comply with relevant legislation.
The class size and candidate/instructor ratio must allow training to be delivered in a safe manner and enable candidates to achieve the learning outcomes.
Learning will use a blend of classroom and practical learning aimed at ensuring the candidate can safely use the pedestrian applicator to effectively install thermoplastic road markings.
This standard is considered to contain 51% or more practical training.
Assessment
Methods of assessment considered appropriate for training delivered against this standard are:
- practical assessment: off the job simulated environment
- theory assessment: classroom, e-learning, or a combination.
Quality assurance
Quality assurance against this standard will require initial approval of the training organisation and their content mapped to the standard.
CITB will also conduct an approval intervention, either desk-based or centre visit, to ensure the training organisation can meet the requirements of the training standard.
Approved training organisations (ATOs) will be required to present information on records of training and assessment upon request to CITB for desk based analysis. They will also be visited annually by the CITB quality assurance team.
Renewal
Recommended Refresher
Approval date
November 2018
Review cycle
Either on request or 3 years from approval date.
Learning outcomes
The candidate will be able to:
- Describe the equipment: HCA lance and a hand-propelled scabbler with compressor
- Compare removal methods: HCA lance, dustless blasting, scabbling, and high pressure water blasting
- Store, handle, and decant fuels such as: LPG, petrol, diesel, and oils
- Perform safe preparation and planning to remove thermoplastic road markings
- Describe the hazards, risks, controls, and safe work practices associated with the equipment
- Set up, pre-use safety check, maintain, shut down, set down, and store the equipment
- Remove thermoplastic road markings using the equipment
- Identify faults and issues with removal of thermoplastic and use of the equipment
- Describe the main legislation, codes of practice, and/or standards, including manual handling, COSHH, and traffic management
Additional guidance to support learning outcome
- Classroom presentations
- Course handouts
- Practical and knowledge test
Additional information
Health & Safety Executive (HSE)
- Control of Substances Hazardous to Health (COSHH)
- Working with substances hazardous to health. A brief guide to COSHH
- Safe use of work equipment (PUWER)
- Work related road safety
- Useful road related links
- Scottish Occupational Road Safety Alliance (ScORSA)
- Roadside precautions
- Risk assessment
- Workplace health, safety and welfare
- Workplace transport safety
- Parking
- A guide to workplace transport safety
- Vehicles at work
- Safe driving: loading & unloading
Gas torch safety from the HSE
- Asphyxiation hazards in welding and allied processes
- Safe use of compressed gases in welding, flame cutting and allied processes
- Safety in gas welding, cutting and similar processes
- COSHH essentials for welding, hot work and allied processes
- Health and safety toolbox: fire safety
- Health and safety toolbox: gas safety
- Safe use of oxy-propane preheating torches
- Approved code of practice and guidance. Dangerous substances and explosive atmospheres
- Controlling fire and explosion risks in the workplace
- Hazardous area classification and control of ignition sources
Legislation
http://www.legislation.gov.uk/
- The PPE at Work Regulations 1992
- Provision and Use of Work Equipment Regulations (PUWER ) (1998 UK 1999 NI)
- The Management of Health and Safety at Work Regulations 1999
- The Health and Safety at Work etc Act 1974
- The Workplace (Health, Safety and Welfare) Regulations 1992
- Health and Safety (Safety Signs and Signals) Regulations 1996
- Fire Precautions and Workplace Regulations 1997
- Reporting of Injuries, Diseases and Dangerous Occurrences Regulations (RIDDOR ) 1995
Standards
- BS EN 1436:2007+A1:2008 Road marking materials. Road marking performance for road users
- BS EN 1424:1998 Road marking materials. Premix glass beads
- BS EN 1423:2012 Road marking materials. Drop on materials. Glass beads, antiskid aggregates and mixes
- BS EN 1463-1:2009 Road marking materials. Retroreflecting road studs. Initial performance requirements
- BS EN 1463-2:2000 Road marking materials. Retroreflecting road studs. Road test performance spec’ns
- BS EN 1463-3. Road marking materials. Part 3. Active road studs
- BS EN 1790:2013 Road marking materials. Preformed road markings
- BS EN 1871:2000 Road marking materials. Physical properties
- BS EN 1871. Road marking materials. Paint, thermoplastic and cold plastic materials. Specifications
- BS 3262-3:1989 Hot-applied thermoplastic road marking materials. Specification to apply to road surfaces