Facebook Pixel
Skip to content

Pointing and jointing advanced

Overview

The purpose of this standard is to provide the candidate with the knowledge and skills to point and joint for façade preservation work.

Duration

Minimum 1 day of 6 learning hours

Purpose/scope

The purpose of this standard is to provide the candidate with the knowledge and skills to point and joint for façade preservation work.

The scope of this standard covers:

  • job specifications
  • personal protective equipment (PPE), respiratory protective equipment (RPE), and safety controls
  • hand and power tools
  • signage, protections, and barriers
  • rake out mortar
  • prepare for pointing
  • point a test area
  • point an area
  • work safely
  • local authority recycling/waste management

Occupational relevance

Training delivered against this standard would be relevant to the following occupational group(s):

  • operative and craft
  • supervision

Candidate pre-requisites

The candidate pre-requisite for this course is the pointing and jointing introduction course.
Before candidates perform facade work at height on a construction site, candidates must have successfully completed specific training for working safely at height.

Instruction/ supervision

As a minimum, course instructors must be able to demonstrate that, in relation to this standard, they have:

  • a train the trainer or instructional techniques course certificate
  • successfully completed training to this standard
  • at least 2 years relevant industrial experience
  • a verifiable CV

Delivery

The following method(s) may be used in the delivery of this standard:

• classroom and workshop

All materials and equipment must be of a suitable quality and quantity for candidates to achieve learning outcomes, and must comply with relevant legislation.
The class size and candidate/instructor ratio must allow training to be delivered in a safe manner and enable candidates to achieve the learning outcomes.

Assessment

For the successful completion of training, candidates must complete an end of course practical assessment or knowledge test that measures the learning outcomes and has a pass or fail criteria.
Quality assurance Quality assurance against this standard will require initial approval of the training organisation and their content mapped to the standard.

CITB will also conduct an approval intervention, either desk-based or centre visit, to ensure the training organisation can meet the requirements of the training standard.

Approved training organisations (ATOs) will be required to present information on records of training and assessment upon request to CITB for desk based analysis. They will also be visited annually by the CITB quality assurance team.

Renewal

No renewal/refreshment requirements - There are no mandatory renewal or recommended refreshment requirements for this standard.

Approval date

November 2018

Review cycle

Either on request or in 3 years from approval date (of the standard)

Learning outcomes

The candidate will be able to:

Interpret job specifications
Select, use, maintain, and store PPE, RPE, and safety controls
Select and install: signage, protections and barriers
Use hand & power tools: select, set up, and pre-use safety check, set down, store, and report defects
Use hand & power tools to rake out mortar
Use hand & power tools to prepare for pointing
Use mortar and hand & power tools to point a test area
Use mortar and hand & power tools to point

Work safely including:

  • follow safe work practices/procedures
  • location of emergency procedures
  • identify hazards
  • reduce/eliminate risks
  • use controls
  • use PPE
  • specific hazards include: water, chemicals, barriers, heights, work platforms, slip, trip, fall, dust, vibration, noise, reduced vision, sharp edges, hot parts, pressurised liquid, abrasives, air pressure valve
  • keep a clean and tidy work area
  • earth leakage protection (residual current device, RCD)
  • extension and power leads (connectors, trips, testing)
  • petrol/diesel fuel (fire, fumes, spills)
  • first aid equipment
  • environmental safety

Confirm and comply with local authority recycling/waste management

Additional guidance to support learning outcome

Examples of:

  • job specifications
  • construction drawings

Videos in classroom
Practical demonstration in workshop
Candidate practice with supervision in workshop
Videos of good and bad practice
Examples of tools and equipment
Examples of operating and maintenance manuals

Examples of:

  • PPE
  • risk assessments
  • safe work practices/procedures
  • spills and clean up
  • environmental legislation
  • safety legislation
  • SDS sheets for COSHH
  • RAMS
  • emergency procedures
  • first aid equipment

Environmental considerations for waste materials

Additional information about this standard

Heritage

HSE Water jetting guides

Training at height

  • BS 8454:2006 Code of practice for delivery of training & education for work at height and rescue
    Advisory Committee for Roof Safety
  • Further information about roof safety: http://www.roofworkadvice.info/index.html

Work at Height Safety Association

The WAHSA technical guidance notes are a free resource, provided and maintained by WAHSA and its member companies for reference. They assist specifiers, managers, and end users of fall protection equipment. http://www.wahsa.org.uk/technical-guidance/

Health & Safety Executive (HSE) Working at height guides

HSE guides

Legislation

http://www.legislation.gov.uk/

  • Health and Safety at Work etc Act (HSWA) 1974
  • The Work at Height Regulations (WHR) 2005
  • Work at Height (Amended) 2007
  • Personal Protection Equipment (PPE) Regulations 2002
  • Personal Protection Equipment (PPE) at Work Regulations 1992
  • Provision and Use of Work Equipment Regulations (PUWER) (1998 UK 1999 NI)
  • Control of Substances Hazardous to Health Regulations (COSHH )2002
  • Lifting Operations and Lifting Equipment Regulations (LOLER) 1998
  • Reporting of Injuries, Diseases and Dangerous Occurrences Regulations (RIDDOR ) 1995
  • Construction (Design and Management) Regulations (CDM) 2015
  • Construction (Health, Safety and Welfare) Regulations 1996
  • Manual Handling Operations Regulations 1992 as amended 2002
  • Control of Noise at Work Regulations 2005
  • Control of Vibration at Work Regulations 2005

Building regulations

  • Building and Buildings, England and Wales: The Building Regulations 2010.
  • The Building (Scotland) Regulations 2004
  • Statutory Rules of Northern Ireland

British standards

https://shop.bsigroup.com/en/

  • BS 8000: 2013 Workmanship on construction sites.
  • BS 8437: 2005 Code of practice for selection, use and maintenance of personal protection systems
  • BS EN 12810-1:2003. Facade scaffolds made of prefabricated components. Product specifications
  • BS EN 12810-2:2003. Facade scaffolds made of prefabricated components. Structural design
  • BS EN 12811-1:2003. Temporary works equipment. Scaffolds. Performance and general design

Grants

Find out how to claim a grant for short duration training courses

ATO course accreditation

Find out how to accredit a training course to a standard.

How did we do today? Give feedback